View SY88149HL_4490281.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

SY88149HL 3.3v 1.25gbps burst-mode limiting amplifier with ultra-fast signal assert timing mlf is a registered trademark of amkor technology, inc. micrel inc. ? 2180 fortune drive ? san jose, ca 95131 ? usa ? tel +1 ( 408 ) 944-0800 ? fax + 1 (408) 474-1000 ? http://www.micrel.com june 2010 m9999-061110-i hbwhelp@micrel.com or (408) 955-1690 general description the SY88149HL is a high-sensitivity, burst-mode capable limiting post amplifier designed for optical line terminal (olt) receiver applications. the SY88149HL satisfies the strict timing restrictions of the gpon standards by providing ultra-fast loss-of-signal (los) or signal-detect (sd) output. auto reset and manual reset options are provided to control los/sd output timing. for increased flexibility, this device also includes an option to select between los or sd output. the device can be connected to burst-mode capable transimpedance amplifiers (tias) using ac or dc coupling. the SY88149HL generates a high-gain los or sd lvttl output. a programmable los/sd level pin (los/sd lvl ) sets the sensitivity of the input amplitude detection. this device also offers the option to choose between a loss-of- signal (los) and a signal-detect (sd) output from the los/sd pin based the los/sdsel pin setting. to select sd output, leave los/sdsel pin open or connect to vcc; to select los output, tie los/sdsel-to-ground. if the input signal amplitude falls below the threshold set by los/sd lvl , los will assert high (or sd will de-assert low). once the input signal rises above the threshold set by los/sd lvl , los will de-assert low (or sd output will assert high). the SY88149HL al so features a jam function which, when active, disables the lvpecl outputs. jam is active low when sd is selected and active high when los is selected. the los/sd output should be fed back to the jam input to maintain output stability under an invalid signal condition. typically, 3db sd hysteresis is provided to prevent chattering. the SY88149HL operates from a single +3.3v power supply over temperatures ranging from ?40 o c to +85 o c. with its wide bandwidth and high gain, signals up to 1.25gbps and as small as 4mvpp can be amplified to drive devices with lvpecl inputs. all support documentation can be found on micrel?s web site at: www.micrel.com . features ? single 3.3v power supply ? <5ns sd assert (los de-assert) time ? option to autoreset or manual reset los output to high and sd output to low ? option to select los or sd output ? up to 1.25gbps operation ? low-noise differential lvpecl data outputs ? 4mvpp input sensitivity ? high sensitivity los/sd detect ? ultra fast lvttl los/sd output ? squelching function to disable output ? programmable los/sd level set (los/sd lvl ) ? available in a 16-pin (3mmx 3mm) mlf ? package applications ? ge-pon/gpon/epon olt ? gigabit ethernet ? fibre channel ? oc-3/12/24 sonet/sdh ? high-gain line driver and line receiver ? low-gain tia interface markets ? ftth/fttp ? datacom/telecom ? optical transceiver
micrel, inc. SY88149HL june 2010 2 m9999-061110-i hbwhelp@micrel.com or (408) 955-1690 ordering information part number package type operating range package marking lead finish SY88149HLmg mlf-16 industrial 149h with pb-free bar-line indicator nipdau pb-free SY88149HLmgtr (1) mlf-16 industrial 149h with pb-free bar-line indicator nipdau pb-free pin configuration 16-pin mlf ? (mlf-16) truth tables los/sdsel function los/sd output (jam input) outputs high sd high enabled high sd low disabled low los low enabled low los high disabled
micrel, inc. SY88149HL june 2010 3 m9999-061110-i hbwhelp@micrel.com or (408) 955-1690 pin description pin number pin name pin function 1, 4 din, /din data inputs. if ac-cou pled, terminate each pin to vref with 50 ? . 2 vref reference voltage output. typically vcc ? 1.3v. 3,11,8 gnd device ground. exposed pad must be soldered (or equivalent) to the same potential as ground pins. 10 /autoreset lvttl input. this pin is internally connected to a 25k ? pull-up resistor and defaults to high. when this pin is low or tied to gr ound, the /autoreset function is enabled and sd de-asserts or los asserts within 100ns (typic al) after the last high to low transition of the burst input. when this pin is left floati ng or not connected, the autoreset function is disabled and the sd de-assert or los assert must be forced by using the manual reset function. 5,16 vcc positive power supply. bypass with 0.1uf | | 0.01uf low esr capacitors. 0.01uf capacitors should be as close as possible to vcc pins. 6 reset lvttl input. apply a high-level signal (>2v) to this pin to discharge the time constant and reset the signal de-assert time or los assert time within 5ns. reset defaults to low if left floating. if the /autoreset function is not used, this reset function needs to be used to quickly de-assert the sd or assert lo s. note that this input is internally connected to a 25k ? pull-up resistor. 7 los/sd lvttl output. signal-detect (sd) assert s high when the data input amplitude rises above the threshold set by sd lvl . conversely, loss-of-signal (los) de-asserts low when the data input amplitude rises above the threshold set by los lvl . 12, 9 dout, /dout lvpecl outputs. when jam disables the devi ce, output dout is forced to logic low and output /dout is forced to logic high. 13 los/sdsel lvttl input. connect to v cc or leave open to select sd; set low or connect-to-gnd to select los. this pin also controls the lo s/sd output and polarity of the jam function. when sd is selected, jam is active low and los/sd (pin 7) operates as signal detect. conversely, when los is selected, jam is ac tive high and los/sd operates as loss-of- signal. note that this input is internally connected to a 25 ? pull-down resistor 14 los/sdlvl voltage input. sets the loss of signal/signal de tect level. a resistor from this pin to v cc sets the threshold for the data input amp litude at which los/sd will be asserted. 15 jam lvttl input. jam acts as a squelch function which can disable the lvpecl outputs. the polarity of the input that triggers an active jam depends upon los/sdsel status. when los is selected, this pin is active high . when sd is selected, this pin is active low. to create a squelch function, connect jam to los/sd output. when jam disables the device, output q is forced to logic low and output /q is forced to logic high. note that this input is internally connected to a 25k ? pull-up resistor.
micrel, inc. SY88149HL june 2010 4 m9999-061110-i hbwhelp@micrel.com or (408) 955-1690 absolute maximum ratings (1) supply voltage (v cc )....................................... 0v to +4.0v input voltage (din , /din) .......................................0 to v cc output current (i out ) continuou s........................................................ 50ma surge .............................................................. 100ma ttl inputs volt age.................................................0 to v cc v ref current .......................................... -800 a to +500 a los/sd lvl voltage............................................v ref to v cc lead temperature (solde ring, 20sec .)..................... 260c storage temperature (t s ) ....................... ?65c to +150c operating ratings (2) supply voltage (v cc )................................. +3.0v to +3.6v ambient temperature (t a ) .......................?40c to +85c junction temperature (t j ) .....................?40c to +125c junction thermal resistance (3) mlf ? ( ja ) still-air ............................................60c/w mlf ? ( jb ) junction-to- board ..........................38c/w dc electrical characteristics v cc = 3.0 to 3.6v; t a = ?40c to +85c, typical values at v cc = 3.3v, t a = 25c. symbol parameter condition min typ max units i cc power supply current no output load 57 78 ma los/sd lvl los/sd lvl voltage v ref v cc v v oh lvpecl output high voltage 50 ? to v cc -2v v cc -1.085 v cc -0.955 v cc -0.880 v v ol lvpecl output low voltage 50 ? to v cc -2v v cc -1.830 v cc -1.705 v cc -1.555 v i offset input offset voltage 1 mv v ihcmr common mode range gnd+2.0 v cc v v ref reference voltage v cc -1.48 v cc -1.32 v cc -1.16 v lvttl dc electrical characteristics v cc = 3.0 to 3.6v; t a = ?40c to +85c, typical values at v cc = 3.3v, t a = 25c. symbol parameter condition min typ max units v ih ttl input high voltage 2.0 v v il ttl input low voltage 0.8 v i ih ttl input high current (/autoreset, jam, los/sdsel) v in = 2.7v v in = v cc 20 100 a a i il ttl input low current (/autoreset, jam, los/sdsel) v in = 0.5v -0.3 ma i ih ttl input high current (reset) v in = 2.7v v in = v cc 200 300 a a i il ttl input low current (reset) v in = 0.5v -0.05 ma v ol ttl output low level i ol = +20ma 0.5 v notes: 1. permanent device damage may occur if absolute maximum ratings are exceeded. this is a stress rating only and functional oper ation is not implied at conditions other than those detailed in the operational sections of this data shee t. exposure to absolute maximum rating con ditions for extended periods may affect device reliability. 2. the data sheet limits are not guaranteed if t he device is operated beyond the operating ratings. 3. thermal performance assumes the use of a 4-layer pcb. expo sed pad must be soldered (or equivalent) to the device?s most nega tive potential on the pcb .
micrel, inc. SY88149HL june 2010 5 m9999-061110-i hbwhelp@micrel.com or (408) 955-1690 ac electrical characteristics v cc = 3.0v to 3.6v; r load = 50 ? to v cc ?2v; t a = ?40c to +85c. symbol parameter condition min typ max units t r , t f output rise/fall time (20% to 80%) note 4 260 ps t jam_lh jam low to high propagation time note 12 5 ns t jam_hl jam high to low propagation time note 13 2 ns t autoreset sd de-assert or los assert with auto reset enabled. 75 100 150 ns t reset reset time constant note 5 5 ns t on sd assert time/los de-ass ert time note 9 5 ns t jitter deterministic random note 6 note 7 15 5 ps pp ps rms v id differential input voltage swing figure 1 4 1800 mv pp v od differential output voltage swing v id > 18mv pp 1500 mv pp sd al /los dl low sd assert/los de-assert level r los/sdlvl = 5k ? , note 8, 10 4.2 mv pp sd dl/ / los al low sd de-assert/los assert level r los/sdlvl = 5k ? , note 10 3 mv pp hys l low sd/los hysteresis r los/sdlvl = 5k ? , note 11 2.9 db sd am / los dm medium sd assert/los de-assert level r los/sdlvl = 2.5k ? , note 10 5.2 12 mv pp sd dm / los am medium sd de-assert/los assert level r los/sdlvl = 2.5k ? , note 10 2.5 3.7 mv pp hys m medium sd/los hysteresis r los/sdlvl = 2.5k ? , note 11 3 db sd ah / los dh high sd assert/los de-assert level r los/sdlvl = 50 ? , note 10 15 24 mv pp sd dh / los ah high sd de-assert/ los assert level r los/sdlvl = 50 ? , note 10 6 9.5 mv pp hys h high sd/los hysteresis r los/sdlvl = 50 ? , note 11 4 db b -3db 3db bandwidth 1 ghz a v(diff) differential voltage gain 48 db s 21 single-ended small-signal gain 42 db notes: 4. amplifier in limiting mode. input is a 200mhz square wave. 5. the time between applying reset and outputs being disabled. 6. deterministic jitter measured using 1.25gbps k28.5 pattern, v id = 10mv pp . 7. random jitter measured using 1.25gbps k28.7 pattern, v id = 10mv pp . 8. sd is the opposite polarity of los. therefore, an sd assert parameter is equivalent to a los de-assert parameter and vice ve rsa. 9. see ?typical operating characteristi cs? for graphs showing input signal vs. sd assert/los de-assert time at various r los/sdlvl settings. 10. see ?typical operating characteristics? fo r a graph showing how to choose a particular r los/sdlvl for a particular assert and its associated de-assert amplitude. 11. this specification defines electrical hysteresis as 20log (sd assert/sd de-assert). the ratio between optical hysteresis an d electrical hysteresis is found to vary between 1.5 and 2 depending upon the level of received optical power and rosa characteristics. based upon that ra tio, the optical hysteresis corresponding to the electrical hysteresis range 2db-5db, shown in the ac characteristics table, will be: 1db-4db op tical hysteresis. 12. jam low to high transition propagation delay refers to the ti me it takes from a low to high transition at jam input to tu rning on (if sd is selected) or turning off (if los is selected) the lvpecl outputs. 13. jam high to low transition propagation delay refers to the ti me it takes from a high to low transition at jam input to tu rning off (if sd is selected) or turning on (if los is selected) the lvpecl outputs.
micrel, inc. SY88149HL june 2010 6 m9999-061110-i hbwhelp@micrel.com or (408) 955-1690 typical operating characteristics v cc = 3.3v, t a = 25c, r l = 50 ? to v cc ?2v, unless otherwise stated.
micrel, inc. SY88149HL june 2010 7 m9999-061110-i hbwhelp@micrel.com or (408) 955-1690 functional block diagram detailed description the SY88149HL is a high-sensit ivity limiting post amplifier which operates on a +3.3v power supply over the industrial temperature range. signals with data rates up to 1.25gbps and as small as 4mvpp can be amplified. figure 1 shows the allowed input voltage swing. depending upon the los/sdsel option, the SY88149HL can generate an sd or los output, and allow feedback to the jam input for output stability. los/sd lvl sets the sensitivity of the input amplitude detection. to satisfy the stringent timi ng requirements of the gpon specifications, the signal detect circuit offers 5ns sd assert (los de-assert) time and the option to de-assert sd (assert los) using the /autoreset or manual reset function. when /autoreset is enabled, sd de-asserts/los asserts automatically within 100ns after the last high-to-low transition of the input burst. when the /autoreset function is disabled, the sd de- assert/los assert time can be reset by using the provided reset pin. input buffer figure 2 shows a simplified schematic of the input stage. the high sensitivity of the input amplifier allows signals as small as 4mvpp to be detected and amplified. the input buffer can allow input signals as large as 1800mv pp . input signals are linearly amplifi ed with a typically 48db differential voltage gain un til the outputs reach 1500mv pp (typ). applications requir ing the SY88149HL to operate with high-gain should have the upstream tia placed as close as possible to the SY88149HL?s input pins. this ensures the best performance of the device. output buffer the SY88149HL?s lvpecl outpu t buffer is designed to drive 50 ? lines. the output buffer requires appropriate termination for proper operation. an external 50 ? resistor to v cc ?2v for each output pin provides this. figure 3 shows a simplified schematic of the output stage. loss of signal/signal detect the SY88149HL generates a chatter-free signal-detect (sd) or los lvttl output, as shown in figure 4. a highly sensitive signal detect circuit is used to determine that the input amplitude is too small to be considered a valid input. los asserts high if the input amplitude falls below the threshold set by los/sdlvl and de-asserts low otherwise. sd asserts high if the input amplitude rises above the threshold set by los/sdlvl and de-asserts low otherwise. los/sd can be fed back to the jam input to maintain output stability under the absence of an invalid signal condition. typically, a 3 db hysteresis is provided to prevent chattering. los/sd level set a programmable los/sd level set pin (los/sd lvl ) sets the threshold of the input am plitude detection. connecting an external resistor between v cc and los/sd lvl sets the voltage at los/sd lvl . this voltage ranges from v cc to v ref . the external resistor creates a voltage divider between v cc and v ref , as shown in figure 5. set the los/sd lvl voltage closer to v ref or more sensitive los/sd detection or closer to v cc for higher amplitude inputs.
micrel, inc. SY88149HL june 2010 8 m9999-061110-i hbwhelp@micrel.com or (408) 955-1690 timing diagrams a) no manual reset & /autoreset tied high b) no manual reset & /autoreset tied low c) manual reset pulse & /autoreset tied low d) manual reset pulse & /autoreset tied low
micrel, inc. SY88149HL june 2010 9 m9999-061110-i hbwhelp@micrel.com or (408) 955-1690 figure 1. vis and vid definition figure 2. input structure figure 3. output structure figure 4. sd output structure figure 5. los/sdlvl setting circuit
micrel, inc. SY88149HL june 2010 10 m9999-061110-i hbwhelp@micrel.com or (408) 955-1690 related product and su pport documentation part number function datasheet link sy88903al 3.3v, burst mode 1.25gbps pecl high- sensitivity limiting post amplifier with ttl loss-of-signal http://www.micrel.com/product-info/sy88903al.shtml sy88149cl 3.3v, 1.25gbps pecl limiting post amplifier w/high gain ttl signal detect http://www.micrel.com/product-info/sy88149cl.shtml application notes notes on sensitivity and hysteresis in micrel post amplifiers http://www.micrel.com/product-info/app_hints+notes.shtml
micrel, inc. SY88149HL june 2010 11 m9999-061110-i hbwhelp@micrel.com or (408) 955-1690 package information 16-pin mlf? (mlf-16) micrel, inc. 2180 fortune drive san jose, ca 95131 usa tel +1 (408) 944-0800 fax +1 (408) 474-1000 web http://www.micrel.com the information furnished by micrel in this data sheet is belie ved to be accurate and reliable. however, no responsibility is a ssumed by micrel for its use. micrel reserves the right to change circuitry and specifications at any time without notification to the customer. micrel products are not designed or authori zed for use as components in life support app liances, devices or systems where malfu nction of a product can reasonably be expected to result in pers onal injury. life support devices or system s are devices or systems that (a) are in tended for surgical implant into the body or (b) support or sustain life, and whose failure to perform can be reasonably expected to result in a significan t injury to the user. a purchaser?s use or sale of micrel produc ts for use in life support app liances, devices or systems is a purchaser?s own risk and purchaser agrees to fully indemnify micrel for any damages resulting from such use or sale. ? 2010 micrel, incorporated.

▲Up To Search▲

Price & Availability of SY88149HL

	To Download SY88149HL Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .